Tips

How much does it cost to replace a circuit board on a furnace?

How much does it cost to replace a circuit board on a furnace?

Depending on how technologically advanced your current furnace is, replacement costs for a new circuit board can run from around $300 to $1,200. While it might seem better to replace the circuit board, stop to consider the age of the furnace.

Can I replace my own furnace circuit board?

If you’ve determined the circuit board is the cause of your furnace problem, it’s a relatively easy part to replace. The circuit board is usually located in the furnace’s blower chamber near the bottom of the unit. Some furnaces will allow you to just remove the lower panel to access the blower chamber.

How do I know if my furnace circuit board is bad?

If a control board starts to break, you will notice some of the following signs of malfunction:

  1. Warning lights. Typically, control boards have LED indicators that function as warning lights.
  2. Temperature instability.
  3. Interruptions in the event sequence.

Are furnace control boards interchangeable?

2 Answers. It turns out they’re not compatible — the one I need is for one-stage, and the other one is for two-stage. I would go back to the person you had working on your AC unit a few months ago and get them to provide the proper replacement.

How much is a new circuit board?

A low-amp subpanel costs from $500 to $1,000 while a 200-amp panel upgrade runs up to $4,000. Total costs depend on the type of home, the number of circuits, and the amperage….Cost To Replace Circuit Breaker Box.

National Average Cost $1,475
Maximum Cost $4,000
Average Range $1,287 to $1,707

How long does it take to replace a circuit board?

Circuit boards can be repaired in one to two days and cost hundreds of dollars less than buying new. Keeping repaired units on hand make for quick on-the-job replacements.

How much should it cost to replace circuit board?

The price to repair an HVAC circuit board is $100 to $600. This job often includes replacing it.

How much does it cost to replace the circuit board?

What causes furnace circuit board failure?

Failed transistors: The transistors in the control board are susceptible to damage due to power surges, static electricity, and age. Transistors are often the first part of a control board to fail. Loose wiring: The vibrations of the furnace over the years can cause wiring in the control board to shake loose.

How much do furnace control boards cost?

If you are a home DIY type of person, furnace control boards can be bought online for $50-$250 dollars depending on the furnace.

How do you reset a furnace control board?

How to Reset an Electric Furnace

  1. First, turn off the power supply to the furnace by turning off the breaker in the circuit box.
  2. Locate the reset button on the furnace and press it to reset the furnace.
  3. If the button is popped up, press it down.
  4. Return the cover to the blower compartment and turn the power on.

What kind of circuit board does a furnace use?

The circuit / control board functions as the brain of your furnace, controlling the gas valve, hot surface igniter and flame sensing circuit. A more efficient type of board, known as the integrated furnace control, also controls the furnace blower in both air conditioning and heating modes.

What to do if your furnace control board is defective?

The control board can malfunction, however, and put your furnace’s operation in jeopardy. When this occurs, you will need to call for professional heating service in Williston, VT to replace the defective board. Red Rock Mechanical can provide this service for you, fast and effectively, when you need it.

What are the model numbers of The KeepRite furnace?

Keeprite Furnace Model Numbers 1 G9MXE0401410A 2 G9MXE0601714A 3 G9MXE0801716A 4 G9MXE1002116A 5 G9MXE1202422A

What does it mean when your furnace is in good order?

Keeping your furnace in good working order means that it’ll be running at peak efficiency and maintaining a comfortable home for you. Open the front panel or door to get access to your Keeprite furnace; you may have to slide or unscrew the panel to work with progressive force.

Share this post