How much water do fire hoses release per minute?

How much water do fire hoses release per minute?

The 1 1/2-inch double jacket fire hose provides 5.06 gallons per minute per dry pound of hose (150 GPM / 29.6 lbs dry = 5.06 GPM/pound). While 150 GPM may be plenty in many situations, this hose trades ease of use for lower flow rates.

How much water is in a 3 inch fire hose?

3-inch hose—water content—per foot of length 0.367 gal. 2 1/2-inch hose—water content—per foot of length 0.255 gal. One 50 ft. length 3-inch hose—contains 156 pounds of water One 50 ft.

How much water does a hose put out per hour?

The flow rate for a garden hose is between 9 and 17 gallons per minute. Depending on the type of hose, the average garden hose can be anywhere from 12 to 13 gallons.

How much water can flow through a 2.5 inch fire hose?

9. A single 2 1/2-inch side discharge can deliver 1,000 gpm efficiently. In fact, if used in a relay pump operation, the 2 1/2-inch discharge can flow up to about 1,800 gpm.

How do you calculate gpm on a fire hose?

The equation EP = NP + FL + APP + ELEV is the basic equation every pump operator needs to calculate when operating the fire pump. Today, many pump panels have flow meters that allow the pump operator to match the readout on the pump panel with the gallon-per-minute (gpm) flow of the selected nozzle.

How do I calculate how much water is in my hose?

The formula for the volume of cylinder is: cylinder volume = π * radius² * height . For a pipe use its length instead of height: pipe volume = π * radius² * length , where radius = inner diameter/2 . The volume of a pipe is equal to the volume of a liquid inside (if a pipe is fully filled with it).

How many gallons of water is in a garden hose?

The capacity of a 100-foot length of 1-inch diameter hose is 4 gallons.

How much water does a hose produce?

Gardeners can rely on estimates even without calculating the hose length. The standard 5/8-inch garden hose delivers 17 gallons per minute. Larger hoses, such as a 3/4-inch hose, use up to 23 gallons per minute. A 1/2-inch garden hose delivers about 9 gallons of water per minute.

How do you calculate gpm of a fire?

Example: For a 30′ x 50′ building that’s 25 percent involved, the flow would be 30 x 50 = 1,500 square feet, divided by 3 = 500 x 0.25 = 125 gpm. Based on that required fire flow, one handline pumped at the correct pressure should be able to produce the required gpm.

How much pressure is coming out of a fire hose?

There is no single flow volume for fire hose. It all depends upon how much pressure you are able to supply in getting the water through the hose line. Then the length of the hose directly affects the amount of pressure it will take. For 1 3/4″ hose at 125 gpm it takes about 16 psi per 100 ft.

How is the volume of a fire hose determined?

The volume of a hose allows an estimate of how much water can be delivered to the fire and is important in firefighting. The hose diameter is usually given in inches, with length in feet. The volume of a hose can be computed using the equation for volume of a cylinder in Section 3.1.

How much water does a 1 inch hose hold?

Find the appropriate estimation in Table 3.1 for the volume of water in both 1-inch and 1-1/2-inch lengths of hose. Each 1-1/2-inch ID x 100-foot hose length holds 9 gallons. Each 1-inch ID × 100-foot hose length holds 4 gallons.

How much does water in hose add to engine weight?

The water in the tank adds 4,000 pounds to the weight of the engine. Example 4 – Two 100-foot lengths of 1 & 1/2-inch cotton-synthetic hose weigh about 54 pounds total when dry. How much will the same hose weigh when fully charged? Step 1. Find the appropriate estimation in Table 3.1.